Installed new gas shut-off valve and replaced gas piping in preparation for utility company meter replacement. Work completed in basement utility area with existing infrastructure, ensuring proper valve accessibility and code-compliant pipe connections to facilitate safe gas service interruption and meter swap.

Replaced existing water heating system with new A.O. Smith tankless water heater unit. Installation included complete copper piping network with isolation valves, expansion tank integration, PVC venting system routed through ceiling, electrical connections with dedicated junction box, and pressure relief components. All connections were tested and system commissioned to manufacturer specifications.

Responded to recurring drain backup issue in kitchen sink approximately one week after initial service call. Upon inspection, assessed garbage disposal unit and associated drain lines beneath sink for blockage or improper drainage. Cleared obstruction from disposal and drain assembly, tested water flow through pedestal bathroom sink and kitchen drainage system to verify proper operation, and confirmed all fixtures draining correctly upon completion.

Responded to a garbage disposal replacement request. Upon arrival, accessed the under-sink cabinet and disconnected the existing disposal unit from the electrical supply and drain plumbing. Removed the old disposal from the sink mounting assembly. Installed new garbage disposal unit, securing it to the existing sink flange with proper mounting hardware. Connected the discharge tube to the existing P-trap and drain assembly using appropriate PVC fittings. Verified electrical connections were secure with wire nuts and confirmed GFCI outlet protection was functioning properly. Tested the new disposal for proper operation, checking for leaks at all connection points and ensuring smooth motor function. Left work area clean and operational.

Responded to service call for two toilet issues in residential bathroom. Successfully cleared clog in first toilet using appropriate plumbing tools and techniques to restore proper drainage and flushing function. Inspected second Kohler toilet that was not filling properly and diagnosed issue with fill valve or water supply. Verified chrome braided supply line connection from wall-mounted shutoff valve to tank inlet was secure and functioning. Tested both toilets after repairs to confirm proper operation, adequate water flow, and complete tank filling. All fixtures returned to normal working condition.

Responded to service call for two shower valve cartridges that were improperly installed by previous contractor, resulting in reversed hot/cold operation in one shower and non-functional pressure balance in the second shower. Upon inspection, identified that replacement cartridges had been installed in incorrect orientation due to keyed cartridge design that was not properly aligned with valve body housing. Removed both pressure balance cartridges, verified manufacturer specifications for proper installation orientation, and determined that supply line configuration required cartridges to be rotated 180 degrees from previous installation. Reinstalled cartridges in correct orientation, ensuring alignment notches matched valve body positioning. Tested both shower valves for proper hot/cold operation and verified pressure balance function was restored. Both showers now operate correctly with appropriate temperature mixing and control.

Responded to residential main sewer drain blockage in basement. Successfully cleared clog in main line running from basement cleanout to street connection using mechanical drain cleaning equipment. Accessed drain through basement floor cleanout, deployed cable snake through line to remove obstruction and restore proper flow. Tested system to confirm full drainage restored. Basement floor drain and surrounding area showed evidence of previous backup with water staining on concrete floor. No structural damage to drain system observed; cleanout cover and access point remain functional. Advised customer that drainage is operating normally.

Installed new garbage disposal unit under kitchen sink, including complete mounting assembly and connection to existing drain system. Configured PVC P-trap drainage with proper venting, connected water supply lines with shut-off valves, and tested all connections for leaks to ensure proper operation of the disposal unit and drainage system.

Responded to service call for outdoor hose faucet that would not shut off. Inspected dual-valve hose bib assembly mounted on exterior wall and diagnosed faulty valve stem washer causing continuous water flow. Replaced worn internal components, tested both valves for proper operation, and verified complete water shutoff with no leakage.

Responded to a bathtub drain that was draining slowly and had completely stopped flowing. Accessed the drain system through the crawl space beneath the residence, where the plumbing lines and P-trap configuration were inspected and serviced to restore proper drainage function.

Completed bathroom re-pipe installation with new PVC piping system. Removed existing plumbing infrastructure and installed replacement supply lines and drain piping throughout the bathroom area, including proper connections at ceiling joists and structural framing members. All PVC joints were properly primed and solvent-welded per code requirements, with purple primer visible at all connection points to ensure quality assurance documentation.

Responded to plumbing service call regarding sulfur odor emanating from garbage disposal when dishwasher was operated. Upon inspection, confirmed that the dishwasher drain line was improperly connected directly to the disposal without proper air gap separation, creating a cross-contamination issue and allowing sewer gases to enter the living space. Additionally assessed basement sewer odor concerns related to potentially compromised P-trap seals or drainage system integrity. Documented existing under-sink plumbing configuration showing garbage disposal unit, PVC P-trap assembly, supply lines, and drain connections for recommended corrective action to separate dishwasher and disposal drain lines per plumbing code requirements.

Completed preventative plumbing inspection of ejector pump, sump pump, and main sewer line as requested following previous flooding concerns. Verified all pump systems were operating properly with no obstructions or mechanical issues detected. Confirmed main sewer line was clear and flowing correctly, with all drainage systems functioning as designed to prevent future flooding events.

Installed hot and cold water shut-off valves in bathroom and replaced broken hot water shut-off valve in kitchen. Upgraded plumbing fixtures with chrome angle stops and flexible supply line connections to provide reliable water control at fixtures. All installations completed with proper threading, compression fittings, and tested for leaks to ensure proper operation.

Responded to water leak complaint originating from upstairs bathroom sink draining into downstairs bathroom ceiling. Upon investigation, accessed crawl space and located improperly sealed drain connection where fabric material had been stuffed around pipe joints as a makeshift attempt to absorb leaking water. Documented existing conditions showing PVC drain line running through floor joists with inadequate sealing at connection points. Identified source of active leak and provided assessment for proper repair of drain assembly to eliminate water intrusion into lower level bathroom.

Conducted on-site assessment for whole home water filtration system installation in residential property. Evaluated basement utility area and existing plumbing infrastructure, including main water supply lines, to determine optimal placement for filtration equipment. Documented current plumbing configuration and available space in mechanical room for future installation planning.

Performed drain line clearing service to remove severe blockage caused by accumulated fibrous material and debris. Utilized specialized hydro-jetting equipment with rotating nozzle attachment to break up and flush obstruction from pipe system, restoring full flow capacity to the affected drainage line.

Responded to recurring faucet leak at bathroom sink for membership plan customer. Upon arrival, found deteriorated chrome-plated wall-mount spout with visible corrosion and finish degradation exposing underlying metal. Removed failed fixture and assessed wall-mounted copper supply pipe, which showed age-related patina but remained structurally sound. Provided on-site quote as requested, then proceeded with replacement of corroded spout assembly. Installed new chrome wall-mount faucet spout with proper escutcheon plate, ensuring secure connection to existing copper stub-out. Tested for leaks under full water pressure and verified proper flow rate and drainage. Documented conditions with photographs showing before and after states of installation.

Responded to a clogged first-floor bathroom tub drain. Upon inspection, found significant mineral buildup and debris obstruction in the drain line. Cleared the blockage using appropriate drain cleaning tools, restored proper drainage flow, and tested the fixture to ensure complete resolution of the clog.

Installed gas pressure regulator and connected flexible CSST gas line to stove supply valve within utility cabinet. Verified proper valve operation and secure connections to ensure safe appliance functionality.