Inspected the ejector pump system in response to reports of excessive cycling during rain events. Located the sump basin beneath the exterior access lid and found a submersible pump heavily coated in sediment and grime, with a corroded basin, mineral and rust buildup on the discharge piping, and cracking and staining in the pit walls. The condition indicates likely infiltration and debris accumulation contributing to the frequent run times, and the basin and pump are recommended for cleaning and further evaluation.

Performed a water leak locate investigation in response to reported moisture behind the bathroom wall, visually inspecting the tub surround, fixtures, and adjacent wall and floor areas. Documented evidence of moisture intrusion, including paint seam cracking at the wall-to-tub transition, staining on the floor tile near the tub and toilet, and ceiling discoloration in the adjacent room below, indicating a probable active leak in the tub-area supply or drain lines.

Cleared a clogged bathtub drain caused by organic debris, which had been aggravated by a prior attempt to treat it with chemical drain cleaner. Removed the obstruction and flushed the drain line, then confirmed the tub now drains freely, with the standing water draining through the chrome drain without backup. Inspected the surrounding fixtures and overflow plate and left the area clean.

Performed annual plumbing maintenance inspection of the plumbing system, with no leaks or operational issues reported prior to service. Inspected the bathroom shower assembly, including the chrome single-handle valve and trim, and noted the shower arm is currently without a showerhead installed. Observed moisture-related wear and staining on the door casing and baseboard trim at the base of the shower enclosure, recommending monitoring for ongoing moisture intrusion.

Performed water heater maintenance and flush, and inspected the repaired drain stack with a camera to evaluate a reported blockage. Observed the PVC drain stack with a wye fitting and cleanout plug connected to the existing metal pipe by a band coupling, and assessed the need for an additional cleanout for future access. Catch basin cleaning was evaluated, with an estimate to be provided prior to proceeding.

Responded to a continuously dripping exterior hose bib and inspected the wall-mounted spigot, mounting flange, and surrounding masonry, where a damp area was observed on the concrete beneath the hose connection. Corrected the leak at the spigot, resecured the flange to the brick wall, and sealed the surrounding mortar joint to prevent moisture intrusion. Verified the fixture operates properly with no remaining drips or leaks.

Performed a plumbing estimate for multiple inoperative water refill stations and the installation of two water shut-off valves. Inspected the mechanical room and noted a brass backflow preventer assembly with worn pipe insulation, along with heavily corroded flanged valves and pipe flanges that may require attention. Evaluated the scope of work needed to restore refill station operation and add the shut-offs.

Performed on-site evaluation for a whole-unit water filtration system installation and modification of the kitchen drain piping to allow a code-compliant dishwasher connection. Inspected the main copper water supply, isolation ball valves, and water meter location in the utility area to determine filtration tie-in and bypass placement, and assessed surrounding wall conditions and clearances for equipment mounting. Documented existing conditions with photos and prepared the scope for a written quote covering the filtration installation and kitchen drain reconfiguration.

Responded to an emergency under-sink water leak and inspected the P-trap, slip-nut connections, and garbage disposal drain assembly, finding corrosion at the disposal mounting flange and a compromised seal. Replaced the worn washers and gaskets, re-seated and tightened the trap and disposal drain connections, and verified a dry, leak-free system under full water flow.

Responded to a warranty callback for a loose toilet with a reported sewer gas odor; removed the fixture, replaced the wax ring, and inspected the closet flange and closet bolts. Reset the toilet on a new wax ring, secured it with the closet bolts, reconnected the supply line, and confirmed a firm, level, leak-free installation with no sewer gas odor.

Performed a sewer camera inspection on the main drain line of a newly purchased home to check for obstructions, damage, or conditions that could cause backups or flooding. Also connected the gas range using a flexible corrugated gas connector from the wall shutoff valve and verified the connection was secure. Documented the work with photos of the appliance connection and the crawl space mechanical and ductwork area.

Performed plumbing piping installation work in a bathroom with the tub access panel opened, exposing the PVC drain assembly, and in an adjacent open wall cavity containing paired vertical copper supply lines with valve fittings. Inspected the copper connections and noted corrosion and flux residue at the lower fittings, then addressed the piping and fittings to restore proper connections with the subfloor and framing left accessible for follow-up work.

Responded to reported sewage backup affecting the toilet and bathtub and performed a camera inspection of the main drain line accessed through the basement cast-iron cleanout. Observed wet floor conditions and standing water around the base of the stack consistent with a mainline blockage, and the inspection was completed to evaluate the line and determine the cause of the stoppage.

Cleared obstructions from the upstairs toilet and bathtub drain lines using drain cleaning equipment, restoring proper flow and drainage to both fixtures. Inspected the tub spout and addressed the dripping faucet, then tested all fixtures to confirm normal operation with no remaining blockages or leaks.

Diagnosed a leak occurring during toilet flush cycles and performed repairs to restore proper sealing and function. Inspected the toilet assembly and associated supply and drain connections, corrected the source of the leak, and tested through multiple flush cycles to confirm no further leakage. Photos taken of the adjacent tub and shower area, including an exposed shower valve access opening in the tile wall, to document existing conditions at the time of service.

Inspected the toilet tank and found significant mineral deposits, grime buildup on the dual-flush valve buttons, and discoloration throughout the tank interior. The customer has a replacement tank on site but is awaiting delivery of internal components (fill valve and flush assembly), so installation was not completed; the customer will contact the office to reschedule once parts arrive, with a follow-up planned if not received.

Performed scheduled maintenance on the Weil-McLain boiler per customer clarification that service was needed for the boilers rather than the tanked water heater. Inspected the boiler, expansion tank, and associated copper and galvanized piping, noting heavy oxidation and rust-colored corrosion with mineral deposits at the dielectric and threaded fittings beside the water heater. Documented the aging piping and corroded connections with photos and recommend evaluation for fitting and union replacement to prevent future leaks.

Replaced the corroded copper-to-steel connection on the boiler supply piping, where galvanic corrosion and mineral buildup indicated a prior leak. Removed the deteriorated steel nipple and collar, installed new dielectric-compatible fittings, and sealed all threaded joints. Pressure-tested the system and confirmed it was leak-free, with the boiler, expansion tank, and surrounding piping operating normally.

Responded to a report of water backing up from the floor drain beneath the water heater during showers and heavy rainfall, indicating a partial obstruction or restriction in the drain line. Inspected the utility closet and surrounding plumbing, confirmed no leaks or visible damage at the water heater or drain pan, and cleared the blockage to restore proper drainage flow.

Serviced a Delta touchless (solenoid-operated) pull-down kitchen faucet. With the water supply shut off at the angle stops, the faucet was removed and the under-sink solenoid valve, electronic control module, braided supply lines, and chrome shutoff valves were inspected and prepared for maintenance. Reinstalled the stainless steel faucet with the soap dispenser in place, restored water supply, and verified proper operation and no leaks at connections.